Lights in a bathroom need an IP rating that matches their zone: IPX7 inside a bath or shower tray, and IPX4 or IPX5 in zones 1 and 2, according to NICEIC. Beyond that, good bathroom lighting layers bright, even light at the mirror with softer ceiling and low-level light, all dimmable and controlled from one place.
What are the bathroom lighting zones?
Electricians divide a bathroom into zones, and each one limits what you can fit. NICEIC describes them like this:
- Zone 0 is the inside of the bath or shower tray, anywhere it can hold water.
- Zone 1 runs from zone 0 up to the highest fixed shower head or 2.25 m from the floor, whichever is higher.
- Zone 2 extends 600 mm outside the boundary of zone 1.
Anything beyond that is outside the zones, though a steamy bathroom still suits a protected fitting. NICEIC notes that IPX4 is usually the minimum rating for a bathroom appliance. The zones are the reason a design drawn up for a bedroom cannot simply be copied into a bathroom.

What IP rating does each zone need?
The IP rating describes how well a fitting resists water. In a bathroom, the second digit matters most:
- Zone 0: IPX7, which is protection against immersion.
- Zones 1 and 2: IPX4 or IPX5, according to NICEIC. A fitting that may be hit by water jets, for example above a powerful shower, needs the higher figure.
Always check the box or datasheet for the rating, not the shop description. If you are unsure which zone a fitting falls in, ask the electrician before it goes into the ceiling. Moving a downlight after the plaster is finished is far more expensive than checking first. NICEIC is also clear that bathroom electrics should be installed by a registered electrician, so this is not a DIY job.
How should you layer light in a bathroom?
A single bright ceiling light is the usual mistake. It makes a flat, harsh room and casts shadows on your face at the mirror. We plan bathrooms in the same layers we use elsewhere in the house, as described in our guide to layering light in a smart home:
- Task light at the mirror. Put light on either side of the mirror, or use a lit mirror, so your face is lit evenly rather than from above.
- General light from the ceiling. Keep it moderate and well spread, so you are not staring up into bare downlights from the bath.
- Soft, low-level light. A low glow under a vanity unit or along a plinth is enough for a night-time visit without waking anyone.
- Feature light. A niche, shelf or textured wall can be picked out for atmosphere.
Each layer sits on its own circuit or channel, so you can raise the mirror light for getting ready and drop everything to a low glow for a long bath.
Can you put a dimmer in a bathroom?
Yes, in most cases. Lighting control is normally placed outside the zones, often just inside the door, and the dimmer must be compatible with the fittings you have chosen. Most flicker and buzz problems come from a mismatch between LED fittings and dimmer, which we cover in why LED lights flicker or buzz on a dimmer. Choose the fittings and the control together, and check the specification of both with your electrician, because requirements for special locations depend on the exact products.
How do scenes make a bathroom easier to use?
A bathroom is used at very different moments: a quick start to the day, a relaxed evening soak, a half-asleep trip at 3am. Rather than flicking several switches, a keypad by the door can recall a scene for each. It follows the approach in our guide to planning lighting scenes room by room. The same scenes can run from a wall keypad, a handset or an app, and can be tied into the rest of the house through Control4.
We are specialists in Lutron lighting control, and you can see how lighting, shading and automation work together across a whole house in our Hampstead project. Our wider smart home lighting and shading service covers bathrooms alongside every other room.

When should you plan bathroom lighting?
Before first fix, while walls and ceilings are open. That is when circuits, cable routes and control positions can be set out properly, and when the mirror, bath and shower positions fix the zones. Retrofitting later is possible in some homes, as we explain in retrofitting smart lighting without rewiring, but it is always a compromise on a bathroom.
If you are renovating and want a second opinion on your lighting plan, you are welcome to visit our showroom in Walton-on-Thames or get in touch, or call 020 3397 9888.
Frequently asked questions
What IP rating do bathroom downlights need?
It depends on the zone. NICEIC says lights inside a bath need IPX7, and lights in zones 1 or 2 need IPX4 or IPX5. Check the zone with your electrician before you buy.
Can I put downlights above a shower?
Directly above a shower is zone 1 or zone 0 territory, so the fitting must have the right rating for that zone. Use only fittings whose datasheet states a suitable IP rating, and have them fitted by a registered electrician.
Is warm or cool white better in a bathroom?
This is a matter of taste, not regulation. Many people prefer a warm-to-neutral white for a relaxed feel, with the option of brighter light at the mirror. Whatever you choose, keep the colour consistent across all fittings in the room.
Can bathroom lights be part of a smart home system?
Yes. Bathroom lighting can be controlled by the same system as the rest of the house, with scenes, schedules and keypads, provided the fittings and controls are chosen together.
Should I do bathroom lighting myself?
NICEIC advises that bathroom electrical work should be done by a registered electrician. Water and mains electricity are a risky mix.